How to Calculate PCD (Pitch Circle Diameter)?
PCD is the short form of
Pitch Circle Diameter; the Pitch Circle Diameter (PCD) is the diameter of
that circle which passes through the center of all the bolts hole or wheel bolts
or wheel rim holes or stud. The
best example is Flanges, there are multiple holes in Flanges, the circle through
the center of these holes is known as pitch circle and the diameter of this
circle is known as Pitch Circle Diameter, in short PCD. Look at the figures and
find PCD of different stud arrangement circle.
Studs: from the definition of stud is “a
large-headed piece of metal that pierces and projects from a surface,
especially for decoration”, shown in figure as different form of stud
arrangement, such- 3 stud means 3 holes; 4 stud means 4 holes; 5 stud means 5
series of holes and so on.
Pitch
circle:
The transverse section of the pitch cylinder normal to the
axis.
Pitch,
Circular:
The distance measuring along the pitch circle between the centers of two
adjacent teeth (holes) on a plane at right angles to the axis of rotation.
The easiest way
calculate the PCD for different number of studs is as follows:
For calculation hole
to hole distance H is an important to calculation. Distance H may be hole’s
center to center or same side to side. R is the diameter of the pitch
circle.
Example-1:
For 3 stud, PCD=
258mm, what would be the holes distance?
360o /number
of holes
= 360o /3 =120 o , half
of 120o is
60o.
Using
Sin rules in triangle,
SIN
= Perpendicular/Hypotenuse= (H/2)/R= H/2R= H/D (Diameter or
PCD)
Or,
SIN = H/PCD
Or,
Sin60o=H/258
Or,
H= 258x Sin60o= 223.45mm, hole to hole
distance.
Similarly,
for 8 holes:
360o /8
=45o, half
is (45o/2)
Sin (45o/2) = H/258
Or,
hole to hole distance, H= 258x Sin (45o/2) =98.73mm;
So, the common formula
is,
Hole to hole distance,
H=
Sin [(360o/hole number)/2]*PCD
Sponsored:
Sponsored:
How Measure Pitch Circle Diameter of Gear?
In order to design, build and discuss gear drive systems it is necessary to understand the terminology and concepts associated with gear systems. Good designers and engineers have experience and knowledge and the ability to communicate their thoughts and ideas clearly with others. The students and teachers who participate in this unit will learn the gear terms and concepts necessary to design, draw and build gear drive systems, and improve their “Gear literacy”.
Fig: Pitch Circle Diameter of a Gear Tooth |
Module
The length in mm of the pitch circle diameter per tooth.
MOD = PCD / N
Number of Teeth
The number of teeth on the gear.
N = PCD / MOD
Pitch Circle Diameter
The diameter of the pitch circle.
PCD = N x MOD
Outside Diameter
The outside diameter of the gear.
OD = (N + 2) x MOD
Center Distance
The distance between the axes of two gears in mesh.
C = PCD(g) + PCD(p)
2
Circular Pitch
The distance between adjacent teeth measured along the arc at the pitch circle diameter.
CP = pi x MOD
Circular Tooth Thickness
The width of a tooth measured along the arc at the pitch circle diameter.
CTT = CP / 2
Addendum
The height of the tooth above the pitch circle diameter.
A = MOD
Dedendum
The depth of the tooth below the pitch circle diameter.
D = H - A
Whole Depth
The total depth of the space between adjacent teeth.
Finer than 1.25 MOD:
H = 2.4 x MOD
1.25 MOD and coarser:
H = 2.25 x MOD
If you interested to know more details about PCD calculation of gear tooth, you may read the full article or even download the pdf file for free from the link below:
PCD-Pitch Circle Diametear Calculation of Gear Tooth
Sponsored:
How Calculate PCD (Pitch Circle Diameter) of a Flange?
The PCD of a flange is one of the most critical dimensions. Now we will try to make easy to find the PCD (Pitch Circle Diameter) of a flange in our daily work.PCD (Pitch Circle Diameter) is the diameter of a circle that goes through each of the bolt holes. Let's see the 8 holes flange at figure below:
Fig: PCD Calculation of a Flange |
Sometimes it’s hard to measure the PCD of a butterfly valve or a flange that’s installed in pipework. Realising your requirement at crutial time, we brought some handy tips to find the PCD calculation of flange having different numbers of holes.
As accurately as you can, measure two adjacent holes using a varniar scale and calculate the PCD; then calculate for-
4 holes: multiply by 1.414
8 holes: multiply by 2.613
12 holes: multiply by 3.864
16 holes: multiply by 5.126
Example:
This 150mm flange has 8 holes and measures 90mm.
PCD = 90 x 2.613 = 235mm
How Calculate Pitch Circle Diameter of a Bolt Thread?
Another difficulty to measure the PCD- Pitch Circle Diameter of bolt or wire thread. Here we brought you some easy and simple way to calculate the bolt thread PCD.Major Diameter: Given On Print (if it is a machine screw #0-14 SEE NOTE 1A).
Pitch: 1/number of threads per inch.
Flat: pitch/8.
Compound Movement: .75(pitch).
Single Thread Height: .75(pitch) (cosine 30 degree’s).
Pitch Diameter: major diameter - single thread height.
Minor Diameter: major diameter - 2 (single thread height).
Vertex Diameter: major diameter - 1.75(pitch) (cosine 30 degree’s).
Best Wire Size (BWS): pitch (tangent 30 degree’s).
Measurement Over Wires (MOW): vertex diameter + 3 (best wire size).
Lead: equals pitch if thread is a single lead.
Pitch Circumference: Pi (pitch diameter).
Lead Angle (Also Called Helix Angle): arc tangent of lead/pitch circumference.
NOTE 1A: Machine Screw Major Diameter: [machine screw# (0.013”)] +0.060”.
Major Diameter of a #10 Screw = [10 (0.013”)] + 0.060” or 0.1900”
EXAMPLE ¾ - 10 UNC BOLT:
Major Dia = 0.750”
Pitch = 1/10” OR 0.1000”
Flat = 0.0100/8 OR 0.0125”
Compound Movement = .75(0.01000”) or 0.0750”
Single Thread Height = .75(0.1000”)(cos 30 deg) or 0.06495”
Pitch Diameter = 0.7500”- 0.06495”or 0.6850”
Minor Diameter = 0.7500”- 2(0.06495”) or 0.6201”
Vertex Diameter = 0.7500”- 1.75(0.1000”)(cos 30 deg) or 0.5985”
BWS= 0.1000” (tan 30 deg) or 0.0577”
MOW= vertex dia + 3(0.0577”) or 0.7716”
Lead is a single lead or 0.1000”
Pitch Circumference = Pi(0.6850”) or 2.1520”
Helix Angle = arc tan 0.1000”/2.1520” or 2.66053 deg [2 deg, 39 min, 38 sec)
NOTE: Helix Angle has to be calculated if you are going to grind threads. The reason is that if the grinding
wheel head is not rotated to the same as the lead angle the thread will have either a drunken lead or a
zero lead, both of which are unacceptable.
Must Remember When Cutting Threads on a Lathe.
Even Pitch Threads 2, 4, 6....Etc: use any line on the threading dial.Odd Pitch Threads 3, 5, 7….Etc: use any numbered line on the chasing dial.
½ Pitch Threads 11½: use #1 or #3.
- Compound rest is always swung to idle side of tool.
- The tool must have the correct thread angle.
- The tool must be sharp.
- The tool must be square to surface being threaded.
- The tool must be on center.
- The compound rest is used to cut thread to correct depth.
- The crosslide is used to maintain a zero point on the “x” axis.
wow, this is nice an uncommon topic but very much helpful.
ReplyDeleteThe Pitch Circle Diameter (PCD) is the diameter of the circle which passes through the centre of all the studs, wheel bolts or wheel rim holes
ReplyDeleteHi! I understand this is somewhat off-topic but I had to ask.
ReplyDeleteDoes managing a well-established blog like yours take a lot of work?
I'm brand new to writing a blog but I do write in my journal on a daily basis.
I'd like to start a blog so I will be able to share my
personal experience and thoughts online. Please let me know if you have any suggestions or tips for new aspiring blog owners.
Thankyou!
Good idea, you could share your experience and good idea to others. So, just start to writing and share, one day it will be like a big tree. You also welcome to write herein this blog, draft your article and mail to wazipoint@gmaill.com or direct send to wazipoint.470620@blogger.com to publish on site.
ReplyDeleteThis article is very informative & helpful for gasket users and ginseal spiral wound gasket manufacturer also.Metal spiral wound gasket is used with the flanges by oil industries to avoid the leakage of flange joints or pipes.it is very useful tools for machinery industries.
ReplyDeleteThank you for your post. This is excellent information. It is amazing and wonderful to visit your site. outdoor optical distribution box
ReplyDeleteTIG welding requires tungsten grinding wheel, electrode, TIG power supply, TIG torch, and shielding gas. Knowing each of these materials can reveal more about the process of welding. Tungsten Darts
ReplyDeleteHow to calcuate PCD by CD
ReplyDelete