WAZIPOINT Engineering Science & Technology: Why Transformer Tap Changing is Required?

Monday, May 15, 2023

Why Transformer Tap Changing is Required?

What is the Principal of Transformer Tap Changers?
Fig-Transformer Tap Changers Line Diagram

What is the principle of Transformer Tap Changers?

We will try to understand the principle of a transformer tap changer and try to find the answer to the question- Can a transformer be tapped when it is on a load? Why is a tap changer used on an HV side?

A tap changer is a mechanism in transformers that allows for variable turn ratios to be selected in discrete steps. Transformers with this mechanism obtain this variable turn ratio by connecting to a number of access points known as taps along either the primary or secondary winding.

A tap is a connection point along a transformer winding that allows a certain number of turns to be selected. This means a transformer with a variable turns ratio is produced, enabling voltage regulation of the output. The tap selection is made with a tap changer mechanism.

You may like to read another post about: 





Can a transformer be tapped when it is on a load?

Yes.
Yes, on-load tap changers are in use to adjust the output voltage of power transformers for a long. OLTC is attached to the power transformers. Control cables run from OLTC to the panel in the control room and it can be operated auto /manually.

Variable autotransformers like Variacs and Power-stats have a sliding contact that allows them to effectively change the tap point by turning a knob while they are under load.

Many power utility systems have large, high-power tap changers that can change the tap point of a distribution transformer under load to compensate for varying demand conditions.

There are two (perhaps three) types of tap changers available, and the difference lies in the question you ask.

Off-load tap changer, sometimes called offline. Which requires load disconnection before the contacts move. There is usually a downstream breaker to interrupt the load during tap changing.

On load tap changer (make before break). The contacts are designed to have a shorting piece and to make contact with the next tap, before relinquishing contact with the first. The shorting piece has to be resistive, to avoid a shorted turn.

On load tap changer (break before make). This is not really on-load, but the break during tap changing is very short indeed. The contacts very nearly bridge across two taps but not quite. No resistance is needed. Interruptions of 0.1 half-cycles can easily be achieved.

The first type is rarely automated, and the second two normally are.

The construction of each is very different, so they cannot be used with swapped duty.


Why is a tap changer used on an HV side?

In this type, the tap changer circuit is placed on the primary side or supply side. As we know;


    Turns ratio        = secondary winding turns (Ns)/ primary winding turns (Np)= Ns/Np.

           Secondary voltage = (supply voltage or primary voltage) / Turns ratio.
It is mainly due to the current magnitude. The HV side has a higher voltage than the LV side but a lowers current than the LV side.

You want as low current as possible to be handled by your tap-changer and, hence, the logical choice of installing the tap-changer on the winding side with the lower current (i.e. HV side).



Transformer Tap changer on Primary Side or HV side:


1) In normal operation the tap changer will be at the 0% position to provide the required designed secondary voltage.



2) If the supply voltage increases or load current decreases there will be an increase in supply voltage which is not desirable. In this case, the tap position in the primary winding will rise towards a positive direction i.e. +2.5%, and hence decreases the Np. This will increase the turns ratio (Ns/Np) and further decreases the secondary voltage.



You may know the details about the electrical transformer from the following articles:
 

  1. Working Principle of Transformer;
  2. Transformer Construction;
  3. Core-type Transformers;
  4. Shell-type Transformers;
  5. Elementary Theory of an Ideal Transformer;
  6. E.M.F. Equation of Transformer;
  7. Voltage Transformation Ratio;
  8. Transformer with losses but no Magnetic Leakage;
  9. Transformer on No-load;
  10. Transformer on Load;
  11. Transformer with Winding Resistance but no Magnetic Leakage;
  12. Equivalent Resistance;
  13. Magnetic Leakage;
  14. Transformer with Resistance and Leakage Reactance;
  15. Simplified Diagram;
  16. Total Approximate Voltage Drop in Transformer;
  17. Exact Voltage Drop;
  18. Equivalent Circuit Transformer Tests;
  19. Open-circuit or No-load Test;
  20. Separation of Core Losses;
  21. Short-Circuit or Impedance Test;
  22. Why Transformer Rating in KVA?;
  23. Regulation of a Transformer;
  24. Percentage Resistance, Reactance, and Impedance;
  25. Kapp Regulation Diagram;
  26. Sumpner or Back-to-back-Test;
  27. The efficiency of a Transformer;
  28. Condition for Maximum Efficiency;
  29. Variation of Efficiency with Power Factor;
  30. All-day Efficiency;
  31. Auto-transformer;
  32. Conversion of 2-Winding Transformer into Auto-transformer;
  33. Parallel Operation of Single-phase Transformers;
  34. Questions and Answers on Transformers;
  35. Three-phase Transformers;
  36. Three-phase Transformer Connections;
  37. Star/Star or Y/Y Connection;
  38. Delta-Delta or ∆/∆ Connection;
  39. Wye/Delta or Y/ Connection;
  40. Delta/Wye or ∆/Y Connection;
  41. Open-Delta or V-V Connection;
  42. Power Supplied by V-V Bank;
  43. Scott Connection or T-T Connection;
  44. Three-phase to Two-Phase Conversion and vice-versa;
  45. Parallel Operation of 3-phase Transformers;
  46. Instrument Transformers;
  47. Current Transformers;
  48. Potential or Voltage Transformers.

3 comments:

  1. Where do we find latest news in telegram?
    Answer : https://t.me/LATEST4EVER

    ReplyDelete
  2. Baccarat (blackjack) game | michaelhillsc.com
    Baccarat is a 샌즈 카지노 가입 쿠폰 casino game for those 온라인 호텔 카지노 who prefer playing against the dealer. A blackjack game is 에볼루션 카지노 사이트 played between 카지노 꽁머니 two teams of 온라인 바카라 게임 two. The dealer takes turns

    ReplyDelete
  3. The content you shared with us is really useful. Thanks for sharing this.

    New tractor Price

    ReplyDelete

WAZIPOINT:
Thank you very much to visit and valuable comments on this blog post. Keep in touch for next and new article. Share your friends and well-wisher, share your idea to worldwide.

You may like the following pages